guide reset

Start with the printer OFF

1. Hold down RESUME and then hold down POWER
2. Release RESUME
3. Press RESUME twice, then release POWER
4. Let green light blink until printer is done futzing
Select function with RESUME press POWER to execute:
presses - light color - function
Number of presses - light color - function
0 presses - green - Test print (or exit service mode on i960)
1 press - orange - EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses - green - EEPROM initialize
3 presses - orange - Reset waste ink counter

1. Remove Cartridge
2. Unplug the AC Power Cord
3. Hold down the RESUME button
4. Release RESUME after plugging in the AC Power cord.
5. Press the RESUME once within 5 seconds and release the RESUME .
6. Press and HOLD RESUME for two seconds or more and release it.
7. Press and HOLD RESUME for two seconds or more and release it.
8. Unplug AC Power Cord to set data.

This Canon Pixma MX340 User Guide Owners Manual contains the information
you need when installing, setup, setting, configuring, maintenance and
troubleshooting, operating instructions the Canon Pixma MX340. This
user’s guide also contains the Software Section providing you with
step-by-step instructions for using your Canon Pixma MX340, and how to
use the supplied software utilities.

Table of contents Canon Pixma MX340 Manual

• Check the Included Items
• Remove the Protective Material
• Connect the Telephone Line
• Turn the Power On
• Install the FINE Cartridges
• Load Paper
• Set Up for Fax Reception
• Select Connection Method
• Install the Software
• Set Up a Wireless Connection
• Use from Additional Computers
• Try Using the Machine
  Try Copying ~ Print Photos from a Computer ~ Send Faxes
• Maintenance
• Specifications

Download

Repair or Reset Canon iP 1880

This is how to reset Canon iP 1880 :

1. Press Resume button and hold for 1 - 2 minutes
2. Open the cover
3. Release the catridge and then put them on again
4. Close The Cover
5. Turn off the printer
6. Turn it on again.

Or you can use IPTool software to reset,

Step 1 : Manual for service mode 

1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.
5. Open Iptool then klik "Reset Main"
   
   Download IPTool

Gota' Canon S-9000, issuing a "7-blink error code"-
#1. How do I enter the Service Codes reset area?

#2. Where can I get a definitions & reset 'menu' for all the error codes on my S-9000?

Page 2.

The
problem started with ink clogs in the printhead. I bought another one
from Canon (about $65.00 cuts), it went OK for 6 mo. then another clog
problem - I could see, this was going to get expensive!

I pulled
out the old Printhead to do experimental 'brain surgery' on it. I [very
carefully] unscrewed the (actual) printing head from the bottom of the
inktank cartridge and carefully lifted it back. There were the (6) Ink
Ports!

I litely cleaned (and flushed) all 6 nozzle ports clear
of all ink residue (plus the strainer ports above), and re-assembled.
Installed (6) new ink tanks [and waited a 1/2 hour for ink to purge air
out of head ports].

Powered-up and of course got the "7" fatal error code blinks and no action from the printhead. "Good Grief"!

Last question on this run - In removing the actual

To everyone who required resetter for Canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648 to reset ink counter on these canon printer model, I found how to reset these canon printers model on PrinterExperts.Blogspot.com. Canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648 is canon all in one printer verison that designed for home and small office.



I don’t know this reset method work or not on canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648 because I don’t have this printer model to try this reset method.



Ready to reset your printer, follow the following steps:

All these steps must be done to reset your Canon MP198, MP258, MP276, MP496, MP558, MP568, and MP648 printer.

A. Entering into service mode

1. Turn off the printer off is the printer power on. And remove the printer USB cable from your computer..
2. While the printer is OFF, press and hold the Start/Stop button on
   the some other canon printers model press Resume/Cancel button.
3. While still holding Start/Stop button or Resume/Cancel button, press and hold the POWER button.
4. When the POWER LED (green light) lit, release the Start/Stop or resume/cancel button (still holding the POWER button).
5. Still holding the power button,   Press the Start/Stop button or
   resume/cancel button TWICE then Release the POWER button. Wait until LCD
   printer to display 0 (zero) number
6. After the display is 0, attach the printer UDB cable to your
   computer, its will detected new device installed (its normal), now go to
   resetting steps

1. Run “service_tool 1050.exe”. you can download the service tool software from this link: ServiceTool_1050.zip
2. service tool 1050
3. Confirm detected USB-port numbers on USB port column.
4. Click “Main button” on Clear ink counter section. Make sure there
   are papers in the paper feed because the printer will print after the
   process is complete.
5. Click “platen button” on the “Clear ink counter” section. The printer will print again.
6. Turn off the printer and then turn the printer on. You printer is ready for use.

Careful Ravine machine models love a microchip that tells the machine how overmuch ink is socialist in the pickup as fountainhead as if the cartridge came direct from Canon. If you are using a refilled or aftermarket pickup in a Canon machine, the ink monitoring software testament solid the use of the pickup. There is, yet, a way to get around the monitoring software.

Arise the instruction below :

* Rotation on your Canon machine and inactivity for the warm-up transform to skilled. Give the printers way threshold and act for the pickup car to arrive to a exhaustive grab.

* Withdraw the cartridge to be replaced and infix the refilled or aftermarket pickup. Intimate the machines make door.

* Act for the printer to observe the new pickup. An incorrectness message will develop up on the choose to say the machine cannot notice the ink stage on the new cartridge.

* Emit on "Yes" to inform that you requisite to use the new cartridge despite the attempt of hurt to the machine if the cartridge leaks.

* Dawn on "Yes" one statesman time to respond that you understand Canon give not be responsible for casualty done to the machine by the new pickup.

* Exhort and concord the "Resume" fix on the machine for at littlest phoebe seconds. The "Uphold" fasten faculty be flashing. If your printer does not hold the "Continue" fix, counsel and intermission the "Ok" or "Balance" add.

* Use the machine as average, holding in purpose the ink monitoring software present not convey the ink steady for the new cartridge.

CanonGENERIC "S"SERIES RESET CODE

(1) Turn off the printer.
(2) Press and hold the RESUME button, then press and hold the POWERbutton.
(3) Release the RESUME button, Next press and release the RESUME button two (2) more times in succession. Note: you are still holding the POWER button). The printers carriage will "reset"
or move momentarily. If the above was properly performed the printer will enter the"Service Mode".
(4) Press the RESUME button 4 times, this will select the clear waste ink counter function. The lamp
will alternate (change) color with each key press.
1. Service/Factory test print out, including ink sensor check.
2. EEPROM - Info printout.
3. EEPROM - Initialization.
4. Reset the Waste ink counter.
5. Printer model setting. (More selections beyond this point - However it is best leave them unaltered - You have been warned!)
After selecting the desired mode (eg 4), press the POWER button to"set" the change, and return to the top of the function selection menu. Press the POWER button again to restart the printer.

This soul run applies for Ravine Image Machine i900D Periodical. This you chance precis and terminated counseling in using the Canon Image Printer i900D Playoff from essential writing work such as how to movement on your machine to advanced printing activity much as adjusting indication calibre for photographs. Free download the Canon Icon Machine i900D Series User Draw download

This is Reseter for reset i320
Service tool you can download at

http://www.divshare.com/download/1246525-8dc

if you like it please give me some coment
good luck friend.

There are some ways to reset waste ink counter in the Canon Pixma iP 1880. Waste Ink counter have full at Canon Pixma iP 1880 marked with The POWER and ALARM lamps flash alternately. If waste Ink have full the printer cannot be used. So, the printer will be able to be used again after reset. You are can use software resetter like GeneralTool or iPTool to reset Canon Pixma iP 1880, you can also do reset manual. Following its way to reset Canon Pixma iP 1880 :

A. Reset Manual.

On reset manual, sometime printer return blinking after turn on again. For reset manual following its way :

* Turn the printer on
* Press and hold Resume button for 1-2 minutes
* Open the printer cover
* Release the catridge and then put catridge again
* Close The Cover
* Turn Off then Turn On again.


B. Using GeneralTool for canon pixma ip 1800 series

Before using GeneralTool for canon pixma ip 1800, printer driver should have been install correcly in the computer.

Using GeneralTool iP 1800...? why do not use GeneralTool iP 1880. Canon Pixma iP 1880 is canon iP 1800 series. Follow this intruction to reset the printer :

* Download software resetter for canon pixma iP1880 from Here
* Before connecting printer to the power suply, press and hold power button then connecting the printer to the power.
* dsacme.blogspot.com
* While hold the power button press reject button for 2 times then release power button.
* Run general tool for canon iP 1880. After the printer know, Click lock release button. ( note : to view locK release menu, min resolution 1024 x 728).
* Then select Set Destination to iP1800 (my canon iP 1880 printer is iP1800ASA)
* Click MAIN and PLATEN button to reset waste ink counter to zero.
* Finally test print by click TEST PATTERN button.


C. Using iPTool software

This is software from Rusia for canon iP series. Using this software give separate experience. this software detect automatically attached printer in the computer. following way reset to use iPTool software :

* Download and ektrak iPtool software, you can download the software from this url :
* Turn on the printer
* Then run iptool software, the software will detect the printer automatically.
* To reset waste ink counter to zero click “Reset Main” and “Reset Platen” button.
* To view the result do test print.

How to Reset Printers Canon MP140, MP160, MP180, MP210, MP220, MP460, MP470, MP500, MP510, MP530, MP600, MP610, MP800, MP820, MP810, MP830, MP960, MP970

1. Start with printer off
2. Press and hold resume Button (triangle in the circle) and click “Power” button. green led should be on
3. While holding the Power button, release the Resume Button.
4. Without releasing the Power Button, click “Resume” button for two times and release Both Buttons.
5. Click “Resume” for four times then soon click “Power” button, to confirm the selected action (reset counter absorber).
6. Turn off the printer and turn on again

First make sure that the power cable and usb cable are connected, before you perform the reset procedure. And download the resetter (DOWNLOAD NOW MP258 RESET)
FIRST STEPS: Entering Service Mode
You have to enter in service mode in order to used the resetter. To do that follow this procedure,

1. Turn off the printer without pulling the power cords.
2. Hold down STOP/RESET button and press Power button.
3. Keep holding down Power button and let STOP/RESET button go.
4. Then Press STOP/RESET button twice then let BOTH buttons go.
5. You will notice that the Alternate Blinking error is gone, this means that the printer is in Service Mode state.

SECOND STEPS: Using the Resetter

1. After you download the resetter, extract it and double click “servicetool.exe”
2. Click Reload Button and you will get a new USB port.
3. Load some papers in your printer and press the “Main” Button once, wait until the printing is done.
4. Then press “EEPROM Clear” button to clear EEPROM.
5. Then press EEPROM button and the printer will print some text.
6. Then power off the printer(sometimes you have to press twice the power button to turn off) and turn on again. and its done!

First thing you need to do is print an EEPROM information page, step number 2 below.
Once you have an EEPROM print you can reset the waste ink counter, if needed, which is step number 4 below.

Service Mode: This printer has a service mode for service-related settings and for performing test prints. The operator panel buttons are used to enter the desired service mode.
Service Mode Operations

With the printer powered off, hold down the resume button and press the power button.
While holding down the power button, release the resume button and press the resume button twice in succession. Now release the power button.

The indicator will blink in green and remain lit in green.
Select one of the following service mode functions by pressing the “RESUME Button” the specified number of times.

1 time = Service test print.
2 times = EEPROM information print.
3 times = EEPROM initialization
4 times = Waste ink counter resetting
5 times = Destination settings
6 times = Print head deep cleaning
Then press the “Power Button” one time to perform the function just selected.

Step 1 Manual for Service mode to reset waste ink or blinking canon ip1500

1. Unplug power and USB.
2. Open door and hold power button.
3. Connect power.
4. Close door, then release power button.

Step 2 Use software for Permanent to reset waste ink
download tool to reset permanent waste ink.
this resetter printer Canon IP 1500. This tool can reset waste ink for canon ip1500 permanent

User guide:

1.
Unzip downloaded file.
2.
Run GeneralTool.exe
3.
Select the connected USB port number from USB port
4.
Click LOCK RELEASE, and select the applicable model name in SET DESTINATION
5.
In CLEAR WASTE INK COUNTER, select MAIN or PLATEN. The selected waste ink counter will be reset. MAIN resets the main waste ink counter, PLATEN resets the platen waste ink counter.

If both the main and platen waste ink absorbers are replaced, reset both the main and platen waste ink counters.

http://www.savefile.com/files/1039880
http://soulved.blogspot.com

his tutorial to answer all question all about software resetter Canon iP2770 and I hope this tutorial info can help all this blog visitors who need tutorial reset Canon iP2770.Canon iP2770 is newest all-in-one canon printer that designed for Home and small office user can print with maximal resolution up to 4800×1200 dpi. This canon printer using cartridge type PG-810, CL-811 (PG-810XL, CL811XL Optional) and using Hi-Speed USB 2.0 interface to connected to computer.

Canon Pixma iP 2770 support for Windows 2000 (SP4 only), Win XP, Vista and Windows 7 and also support for MAC OS: Macintosh OS X 10.4.11 – 10.6.
Here the tutorial reset for Canon ip2770 (Click the picture below to view the tutorial – the tutorial are is English and Thai language)

Note: All Download link and tutorial is taken from Thailand printer forum (http://www.compute.co.th). Use this info and tutorial as your own risk. Here the download link software resetter for Canon iP2770:Canon iP2770 Resetter

Beneath recitation set methods for Machine Ravine MP140, MP160 and MP180

1. Turn with printer off
2. Counsel and break uphold Fix (trilateral in the shape) and depression "Power" fix. green led should be on
3. Spell retentive the State switch, conclusion the Resume Switch.
4. Without releasing the Land Fasten, clink "Resume" fix for two times and discharge Both Buttons.
5. Stop "Resume" for foursome present then presently plosive "Power" add, to confirm the elect activeness (adjust calculator absorber).
6. Turning off the printer and transport on again

Follow the step below to to reset Canon i850, i950, Waste Ink

1. Start with the printer OFF
2. Hold down RESUME and then hold down POWER
3. Release RESUME
4. Press RESUME twice, then release POWER
5. Let green light blink until printer is done futzing
   

Select function with RESUME press POWER to execute:

presses – light color – function

Number of presses	light color	function
0 presses	green	Test print (or exit service mode on i960)
1 press	orange	EEPROM info print (plus grid nozzle diagnostic on i960)
2 presses	green	EEPROM initialize
3 presses	orange	Reset waste ink counter

Mostly, Ravine resetter programs change twin resetting work except for any models. So that fortunate resetting canon printers using writer ride all enter attributes of software resetter should not be feature exclusive and dont run the software from CD. There are two variation of pervading way for ravine printer that is with enclosure announcement add and do not jazz Interlace Activity fix.

For resetter with Embrace Give secure (launch internal the possible file)
1. Run generaltool.exe or the application or executable file.
2. Select USB port of the printer to be reset.
3. Click lock release button.
4. IN Select Destination option, select the printer model.
5. In Test Print option, select EEPROM clear.
6. Prepare a paper and then click test pattern 1 under Test Print option.
7. Turn off the printer and turn on again.

For resetter which do not have Lock Release button
Run generaltool.exe or the program or workable line.
Select USB side of the printer to be set.
In Select Destination deciding, superior the printer mold.
In Try Create deciding, superior EEPROM unobstructed.
Modify a theme and then stop endeavour ornament 1 under Judge Exposure option.
windup it